How to check your oven temperature, and how convection and pans change a bake
Check your oven's real temperature with a thermometer or the maker's bake test, time the preheat, set racks and convection, and treat the pan's material, color and size as part of the recipe: glass and dark pans bake differently from light metal.
- Start here: the essentials
- How an oven holds its temperature
- Checking your oven
- Calibrating, or keeping the offset on a card
- Preheating
- Racks and where the pan sits
- Convection and countertop ovens
- Pans: material and color
- Pan size
- See it: an oven that runs hot
- Practice: check your oven at 350 °F
- Your kitchen
- Check your work
- Knowledge check and scenario
Start here Essentials
For a first pass, find out what your oven really does at 350 °F (177 °C) and write it down. One afternoon with an oven thermometer does it; without one, the maker's bake test in the green box below is the alternative.
- Put an oven thermometer on the center rack, or borrow one (checking your oven).
- Set the oven to 350 °F and wait 15 minutes after it says it is ready. The extra wait lets the walls and racks catch up (preheating).
- Read the thermometer three times, five minutes apart, and average the readings. Open the door as briefly as you can (how an oven holds its temperature).
- Write the difference from 350 on the oven check. A positive number means the oven runs hot (keeping the offset).
Minimum time: about 45 minutes, most of it waiting. Done when: the oven check shows a dated average reading and the offset.
How an oven holds its temperature Understand
An oven dial or keypad sets a target, not a reading. A thermostat, the control that switches the heat, turns the element or burner on until the oven passes the target, off until it falls below, and on again. The temperature inside swings around the set point all the time the oven is on. Whirlpool's help page describes it this way: the elements cycle on and off to hold the temperature, and the oven may run slightly hot or cool at any point in the cycle (Whirlpool, Oven Temperature Incorrect). Physical principle
Two things follow. One reading is one moment: a thermometer read at the top of a cycle says the oven is hot, and read at the bottom says it is cool. And the average over the cycle, not any single number, is what a cake feels over 30 minutes. ThermoWorks, a thermometer maker, makes the same point and recommends logging the high and low of the cycle and averaging them (ThermoWorks, Oven Temperature).
How far ovens are off
We found no agency figure for how far a typical home oven swings or drifts. The figures that exist come from testers and makers:
- Which?, the UK consumer association, tests ovens in its lab. It found ovens set to 180 °C (356 °F) that reached 220 °C (428 °F), and its least accurate oven ran 40 °C over the set temperature (Which?, Oven temperature conversion).
- Appliance makers build an adjustment into the control so owners can correct the temperature: up to 35 °F either way on GE's up-and-down-pad models and 30 °F on Whirlpool's (calibrating). Whirlpool says ovens can drift as they age.
- ThermoWorks logged nearly 100 degrees of difference between the corners of a high-end convection oven set to 375 °F, and notes that an oven can be accurate at 350 °F and not at 425 °F.
So an unchecked oven's real temperature is unknown. It may be right; it may be 20 or 30 degrees off, which is enough to brown the outside of a loaf before the middle sets. Checking costs one afternoon.
Checking your oven
We found no extension service or agency procedure for checking a home oven with a thermometer. The routine below is ours, built from what the makers and testers say: an oven thermometer where the food sits, the oven given time to settle, and several readings averaged so one peak or trough does not decide it. Test it
- Use an oven thermometer, the kind that stands or hangs on a rack and stays in the oven. Which? suggests a stainless steel one. ThermoWorks notes that common dial models mark every 10 °F and have no adjustment, so read to the nearest mark and do not expect more.
- Put it in the middle of the center rack, where a single pan would sit. ThermoWorks places its sensor near the center for the same reason.
- Set the oven to 350 °F (177 °C) and let it preheat until it signals that it is ready.
- Wait 15 minutes more. A signal tells you the air near the sensor reached the set point once. The walls, racks and thermometer need longer.
- Read the thermometer three times, five minutes apart. Open the door just enough to read it, or read through the window with a flashlight if the glass is clear. Each opening lets heat out.
- Average the three readings: add them and divide by three.
- Work out the offset: the average minus 350. A positive number means the oven runs hot; a negative number, cool. Write the date, the three readings, the average and the offset on the oven check.
Three readings is a small sample. If the three are far apart, say 330, 380 and 350, the oven's swing is wide and three numbers may not catch its middle. Take three more and average all six.
The maker's alternative: a bake test
Whirlpool takes the other side. Its help page tells owners not to judge an oven's temperature with a thermometer, because most are slow to react to the cycling (Oven Temperature Incorrect, above). In its place it gives a bake test (Whirlpool, How to Evaluate if Temperature Calibration is Needed): Product-specific
- One can of refrigerated biscuits on a shiny aluminum cookie sheet with sides no higher than 1/2 inch, the biscuits 1 to 2 inches apart.
- Rack in the middle, at least 2 inches of space to the oven walls, no foil or oven liners.
- The package temperature for a shiny sheet; 25 °F lower than the package for a dark or nonstick sheet.
- Preheat fully until the signal, or 12 minutes if there is none. Do not open the door before the package's shortest time.
- The oven is correct if the biscuits are done and evenly browned within the package's time range.
The bake test needs no thermometer, which is why it is the Start here alternative. It tells you whether the oven bakes as expected, not by how many degrees it is off, so it is slower to act on. Use the thermometer if you can borrow one, and keep the bake test as a second opinion.
Thermometer or bake test: who says what
Whirlpool's product-help page recommends the bake test over a thermometer. Which? and ThermoWorks recommend a thermometer: Which? suggests moving it to different positions, and ThermoWorks logs highs and lows and averages them with an electronic probe. The two positions answer different questions. A thermometer measures the air at one point; a bake test measures what food experiences. A slow dial thermometer smooths out the cycle, which is a weakness for catching the swing and a help for reading the average.
Checking at 425 °F as well
ThermoWorks notes an oven can be right at 350 °F and wrong at 425 °F. If you bake bread, pizza or pastry hot, repeat the routine at 425 °F (218 °C) and write a second row. If the two offsets differ, use the one nearer the temperature you are baking at.
Finding hot spots
Which? advises moving the thermometer to different positions. Repeat the check with the thermometer at the back left, then the front right, of the center rack. A difference of more than a mark or two tells you to turn pans halfway through a long bake.
Calibrating, or keeping the offset on a card
Once you know the offset, there are two ways to use it.
Calibrate the control, if your oven allows it. Calibration here means entering an offset on the oven's control, so that when you set 350 °F the oven aims for a different internal target. Makers build this in. The steps depend on the control, and your owner's manual is the authority for your model. Ask the authority
- GE lists separate procedures for touch screens, settings menus, keypads and knobs. On models with up and down pads, the offset goes up to 35 °F hotter or cooler, in 1-degree steps, and starts at 0. The adjustment does not change broil or self-clean, and it is kept after a power failure. GE's advice is to make small adjustments and test (GE Appliances, Oven Calibration with up and down pads; index of other controls at How to Calibrate My Oven).
- Whirlpool gives several control methods, with steps of 5 °F or 10 °F and a range of 30 °F hotter or cooler (Whirlpool, How to Calibrate the Oven). Its bake-test page says to change the setting by no more than 10 degrees at a time and retest after each change.
The direction is easy to get backward. An oven that runs 20 °F hot needs the offset lowered, toward −20, so it aims cooler.
Or keep the offset on a card. If the control has no adjustment, if you rent and would rather not change it, or until you have read the manual, write the offset on the oven check and set the dial to correct for it. An oven 20 °F hot gets set to 330 °F for a recipe that says 350 °F. This works as well as calibrating, as long as everyone who uses the oven knows. Convention
This manual gives no repair or electrical advice. An oven that will not reach temperature, that reads further off than its maker's adjustment range allows (35 °F for GE's up-and-down-pad models, 30 °F for Whirlpool's), or whose reading changes a lot from one check to the next, goes to the owner's manual and the maker's service line. A gas smell goes to your gas utility, not to an oven thermometer.
Preheating
Preheating is running the empty oven until it reaches the set temperature, before the food goes in. Batters and doughs depend on heat arriving on schedule: a cake set into a cold oven rises and sets on a different timetable from the one its recipe was tested on.
How long it takes depends on the oven. Two makers' figures:
| Maker | Oven | Typical preheat |
|---|---|---|
| GE | Electric with a visible bake element | 5 to 10 minutes |
| GE | Electric with a hidden bake element, or gas | 15 to 20 minutes |
| GE | Hidden element with Fast Preheat | 7 to 10 minutes |
| KitchenAid | Wall ovens and ranges, to 350 °F with all racks in | 12 to 15 minutes |
Sources: GE Appliances, Preheat Time Too Long; KitchenAid, Long Pre-Heat Times for Oven.
GE adds that each 25-degree step above 350 °F adds about 45 to 60 seconds, each extra rack about 30 seconds, and a 208-volt supply instead of 240 volts about 25 percent. KitchenAid tells owners to take unused racks out because they lengthen preheating. A cold kitchen and a large new oven cavity also slow it (Whirlpool, Oven Temperature Incorrect, above).
When to put the food in
Our default is the maker's instruction: KitchenAid says to put food in when the preheat tone sounds. Your oven's manual says what its signal means. If your oven check shows a low reading right after the signal, give it a few more minutes before baking; the Home Baking Association's chart suggests waiting an extra five minutes after preheat (Home Baking Association, Baking Temperatures chart). Product-specific
The 15-minute wait in the oven check routine is longer on purpose. It is for measuring the oven at rest, not for baking.
Racks and where the pan sits
Whirlpool gives the plainest rack guidance we found (Oven Temperature Incorrect, above): Product-specific
- A single rack works best for most baked goods.
- The middle rack suits most baked goods, cookies, layer cakes and casseroles.
- The bottom rack is generally for roasting meats.
- With more than one rack in use, spread them out so air can move between them.
- Pans should not touch each other or the oven walls, which creates hot spots.
- Do not cover a whole rack or the oven bottom with foil.
KitchenAid adds one exception: insulated cookie sheets and stainless steel pans go in the bottom third of the oven, with a slightly longer time (KitchenAid, What Bakeware Should be Used). Recipes that name a rack position, such as a pie baked low to brown its bottom crust, are telling you something about that recipe; follow them.
The default for this manual: one pan, center rack, middle of the rack, with space around it. Two sheets of cookies at once means two racks spread apart and, often, swapping and turning the sheets halfway, which the recipe usually says.
Convection and countertop ovens
A convection setting runs a fan that moves hot air around the food. Moving air carries heat to the food faster than still air at the same temperature, so most recipes written for a standard oven bake faster or brown more in convection. Physical principle
The common correction is to lower the temperature by 25 °F (about 14 °C). Two makers say so, and both say some ovens do it for you:
- LG: its convection modes lower the set temperature by 25 °F automatically, a feature it calls auto conversion, turned on by default. Enter 350 °F and the display shows 325 °F after preheating. If auto conversion is off, lower the recipe temperature by 25 °F yourself (LG, Understanding Convection Cooking).
- Whirlpool: some ovens convert standard time and temperature on their own, and the displayed value may differ from what you entered. Its example is the same: set 350, see 325 after preheat. The owner's manual says whether a model converts (Whirlpool, How to Tell if Convection Conversion Temperature is Correct).
So "convection means 25 °F lower" is two makers' rule, not a law. The risk is lowering twice: an oven that already converts, plus a cook who lowers the dial too. Your manual decides. If it does not say, set the oven to the recipe temperature in convection mode and watch the display after preheat. Ask the authority
The oven converter applies the 25 °F convection rule, your offset and a pan adjustment together, and shows each step.
Countertop and toaster ovens
The maker pages we read are written for full-size ovens, and two bakeware makers exclude countertop ovens outright: Reynolds says its parchment is not for toaster ovens, and Pyrex says its glass bakeware is not for toaster ovens, air fryers or other countertop appliances (both below, under pans). The countertop oven's own manual is the authority on what can go in it, how hot it runs and whether its convection setting converts. Check its temperature with the same routine, using the rack position you bake on. Ask the authority
Recipes that say "fan"
UK recipes often give two temperatures, one conventional and one "fan," for a convection oven. Which? puts fan settings 20 °C below conventional: gas mark 4 is 350 °F, 180 °C, or 160 °C fan (Which?, above). That is a slightly larger cut than LG's 25 °F (14 °C), and it is a convention for UK ovens, not a maker's instruction for yours. Temperature has the full gas mark table.
Makers' convection rules compared
LG lowers by 25 °F automatically and tells owners to lower by 25 °F when auto conversion is off. Whirlpool says some models convert on their own and points to the manual. LG also says baking on several racks may lengthen some times slightly, even though overall time is shorter.
Pans: material and color
A pan is part of the recipe. It sits between the oven and the batter and changes how fast heat gets in. KitchenAid's guidance, for its wall ovens and ranges (What Bakeware Should be Used, above): Product-specific
| Pan | What it does | KitchenAid's adjustment |
|---|---|---|
| Shiny, light aluminum | Reflects heat; light, even browning | Standard time and temperature, center rack |
| Dark aluminum and nonstick | Absorbs more heat; browns faster | Lower by 25 °F (15 °C) for cakes, cookies and quick breads; keep the recipe temperature for pies, artisan yeast breads and casseroles where a crisp crust is wanted |
| Ovenproof glass and ceramic | Heats slowly, holds heat longer | Lower by 25 °F (15 °C) |
| Insulated sheets, stainless steel | Slow to heat | Bottom third of the oven, slightly longer time |
The default in this manual is the light aluminum pan, because recipe writers usually test on one and Whirlpool's bake test specifies one. If your pans are dark or glass, the adjustment above is the starting point, and your first bake in that pan tells you more. King Arthur makes the same physical point in its pan-size guide: glass and ceramic conduct heat more slowly than metal, and dark metal browns most (King Arthur Baking, How to swap baking pan sizes).
Glass bakeware
Glass bakeware can break from a sudden change in temperature. Pyrex's use-and-care page names three risks, breakage from temperature change, breakage from impact, and burns, and gives these instructions (Pyrex, Safety and Usage): preheat the oven before the glass goes in; do not add liquid to hot glassware; do not set hot glass on a wet or cool surface, a countertop, metal or in the sink, but on a rack, dry potholder or dry cloth; do not go from freezer to hot oven; do not use it on a stovetop, under a broiler, on a grill, or in a toaster oven, air fryer or other countertop appliance; and do not use a dish that is chipped, cracked or badly scratched. Follow your own dish's maker if it says otherwise.
Iowa State University Extension's AnswerLine explains why brand alone does not tell you what you have. US-market Pyrex-brand kitchenware moved from borosilicate glass to tempered soda-lime glass after the brand's 1998 sale; soda-lime handles sudden heat less well and resists breaking when dropped. AnswerLine reports that the all-capitals PYREX marking is the older borosilicate glass and lowercase pyrex is soda-lime (Iowa State AnswerLine, Glass Kitchenware Cautions).
Pyrex's page gives no oven temperature limit and no advice to lower the temperature for glass. The 25 °F reduction above is KitchenAid's, an appliance maker's, not the glass maker's.
Parchment and silicone mats
Liners have their own limits from their makers. Product-specific
- Parchment paper. Reynolds says its parchment is oven safe up to 425 °F, should go into a preheated oven, should not touch an open flame or the oven sides, and is not for broilers or toaster ovens. Wax paper is not oven safe (Reynolds, Parchment Paper). Other brands print their own limit on the box.
- Silicone baking mats. Silpat's technical sheet gives a recommended range of −40 °F to 428 °F (−40 °C to 220 °C), with a short peak of 464 °F (240 °C) for no more than five minutes (Silpat technical sheet, hosted by a retailer). The same sheet notes that an oven's displayed temperature may not match its actual temperature, which is a reason to know your offset before baking near a liner's limit.
If something in the oven catches fire, the National Fire Protection Association's instruction is short: "For an oven fire, turn off the heat and keep the door closed." If the fire does not go out, get out, close the door behind you, and call 9-1-1 or the local emergency number once you are outside (NFPA, Cooking safety). The U.S. Fire Administration counts cooking as the leading cause of home fires and home fire injuries; its page covers the stovetop, and says to stay with the pan and keep a lid or baking sheet nearby to smother a pan fire (USFA, Cooking Fire Safety).
Dark pans: two makers, two rules
KitchenAid lowers the temperature 25 °F for dark and nonstick pans, except for pies, artisan breads and casseroles. Whirlpool's bake test lowers it 25 °F for a dark or nonstick sheet with no exceptions. Both are appliance makers writing for their ovens. For cakes, cookies and quick breads they agree; for a pie in a dark pan, KitchenAid's exception is the one written for that case.
When adjustments stack
A dark pan, a glass dish and convection each carry a 25 °F reduction from one maker or another. No source we found says whether to apply two of them together, for example a dark pan in convection, or by how much. Our suggestion, labeled as ours: apply one reduction, check early, and write the result on the bake log so the next bake in that pan starts from what happened. Test it
Pan size
A recipe's pan size sets how deep the batter sits, and depth sets how long the heat takes to reach the middle. Swap pans and the time changes, even at the same temperature. Physical principle
King Arthur Baking's figures (How to swap baking pan sizes, above):
- An 8-inch square pan and a 9-inch round pan, both 2 inches deep, hold about the same: roughly 128 cubic inches, 8.8 cups.
- A 9-inch round holds 26.6 percent more than an 8-inch round. The arithmetic is area: a circle's area grows with the square of its width, so 9 inches across is about 64 square inches and 8 inches about 50.
- Fill pans for creamed-butter and one-bowl oil cakes half to two-thirds full.
- In a smaller pan, fill no more than two-thirds and expect 10 to 15 minutes longer. In a larger pan, start checking 10 to 15 minutes early.
- An 8 1/2 × 4 1/2 inch loaf pan is the "standard" one-pound loaf; a 9 × 5 holds nearly a cup more, almost 20 percent.
- Chiffon, angel food and sponge cakes are poor candidates for pan swaps.
Measure a pan across the inside of the top edge, not the outside, and measure its depth. To find its volume, NIST suggests weighing the water it holds, since water weighs about 1 gram per milliliter. NIST's approximate volumes include a 23 × 33 cm (9 × 13 inch) pan at 3.5 L, a 20 cm (8 inch) round at 1.2 L, a 23 cm (9 inch) round at 1.5 L and a 23 × 13 cm (9 × 5 inch) deep loaf at 2 L (NIST, Cookware and Tools).
Write each pan you own, its inside size, material and color on the pan inventory. The pan converter scales a recipe from one pan to another by area, and the pan reference lists common sizes. Cakes and frosting applies this to layer cakes.
See it: an oven that runs hot See it
Dana Reyes is fictional, and every fact about her here is invented for this manual. She lives in an apartment near sea level and bakes in a full-size electric oven nobody has checked, on one light aluminum sheet pan and in a 9 × 5 loaf pan. Her chocolate chip cookies spread flat and her banana bread is gummy in the center. A friend lends her a dial oven thermometer.
She sets it in the middle of the center rack, sets the oven to 350 °F, and waits 15 minutes after the preheat signal. Her three readings, five minutes apart: 372, 366 and 372 °F.
Known: the average is (372 + 366 + 372) ÷ 3 = 370 °F, so at 350 her oven runs 20 °F hot at the center of the rack. That is inside both makers' adjustment ranges, so it is a calibration question, not a service call. Her pans are light aluminum, the baseline, so no pan adjustment applies.
Assumed (Dana's assumption): that the oven is off by the same 20 °F at 375 °F, the temperature her cookie recipe uses. ThermoWorks notes an oven can be right at one setting and wrong at another, so this is a working assumption until she checks at 375.
Open: whether her thermometer itself reads true (a second thermometer, or the maker's bake test, would settle it); whether the offset holds at 375 °F (a second check settles it); whether her model allows calibration (her owner's manual); and whether the hot oven explains the flat cookies and the gummy loaf. A hot oven can brown the outside of a loaf before the center sets, and that is a reasonable thing to test, but one reading does not settle a cause. When a bake goes wrong takes the checks in order.
She writes a row on the oven check: set 350, readings 372, 366, 372, average 370, offset +20, thermometer on the center rack. Under "what you will do about it" she writes that she will set 330 °F for a recipe that says 350 °F until she has read the manual.
Jun Park (fictional) bakes in a studio apartment with only a countertop convection oven and one quarter-sheet pan. A cookie recipe says 350 °F on parchment. Known: Reynolds says its parchment is not for toaster ovens, and LG and Whirlpool describe convection reductions for full-size ranges, not countertop ovens. Assumed: nothing yet. Open: whether his oven's manual allows parchment or recommends a liner, and whether its convection setting lowers the temperature by itself. His manual settles both, and the oven check routine, run on the rack position he bakes on, tells him its offset.
- Whirlpool, How to Evaluate if Temperature Calibration is Needed: the maker's biscuit bake test, step by step.
- ThermoWorks, Oven Temperature: why one reading misleads, with a logged oven cycle.
- GE Appliances, How to Calibrate My Oven: the calibration steps for each GE control type.
- KitchenAid, What Bakeware Should be Used: the pan adjustments in one short page.
Practice: check your oven at 350 °F Practice
Minimum: one check at 350 °F with three readings, averaged and written on the oven check. Without a thermometer, the maker's bake test with a can of refrigerated biscuits, written in the same sheet's method column. Time: about 45 minutes, mostly waiting; 30 minutes more for a second check at 425 °F. Materials: an oven thermometer (bought or borrowed), oven mitts, a timer, and the oven check. For the bake test: one can of refrigerated biscuits and a shiny aluminum sheet with low sides.
- Take unused racks out and set the thermometer in the middle of the center rack.
- Set the oven to 350 °F and note how long it takes to signal; write it in the method column.
- Wait 15 minutes after the signal.
- Take three readings, five minutes apart, opening the door as briefly as you can.
- Average them and work out the offset. Write the row.
- Decide what to do about it: calibrate by your manual, or set the dial by the offset, and write that in the last column.
- Write your pans on the pan inventory: inside size, depth, material and color.
Check at 425 °F (218 °C) the same way, and write a second row.
Map the rack. Repeat the 350 °F check with the thermometer at the back left and then the front right of the center rack.
Run the bake test as a second opinion after calibrating or adopting an offset, and see whether the biscuits finish within the package's time.
Measure a pan's volume by weighing the water it holds to the brim, and write it on the pan inventory.
Your kitchen Your kitchen
Check your work Check your work
Criteria
- Does the oven check show a date, the set temperature, at least three readings, the average and the offset?
- Was the thermometer in the middle of the center rack, and did the oven settle 15 minutes past its signal before the first reading?
- Is the offset's sign right: positive for an oven that runs hot?
- Is there a decision written down: calibrated, or a corrected dial setting?
- Do you know whether your oven's convection setting converts on its own?
- Are your pans written down with material and color, so the pan adjustment can be applied?
Worked example
Dana's row meets the first four criteria: dated, three readings, an average of 370 and an offset of +20, with a decision to set 330 °F for 350 °F recipes. The convection criterion does not apply to her oven. Her two pans are light aluminum, so no pan adjustment applies, but she has not yet written them on the pan inventory. Her conclusion holds at 350 °F; at 375 °F it rests on her assumption that the offset is the same, which a second check settles.
Common mistakes
- Reading at the signal. The signal means the air near the sensor reached the set point once. Wait 15 minutes for a check.
- One reading. It catches one moment of the cycle. Take three, five minutes apart.
- Turning the offset the wrong way. A hot oven needs a lower setting.
- Lowering twice for convection. If the oven converts on its own, do not lower the dial too. Read the manual or watch the display.
- Glass from the refrigerator into a hot oven, or onto a wet counter. Pyrex warns against both.
- Parchment above its limit. Reynolds rates its parchment to 425 °F; a 20 °F hot oven set to 425 is past it.
What is still unresolved
This chapter cannot tell you whether your thermometer is accurate; a second thermometer or the bake test comes closest. It cannot repair an oven that will not hold temperature; the owner's manual and the maker's service line can. It does not say whether a hot oven caused a particular failure; When a bake goes wrong puts the oven in its place among the other causes. Ingredient temperature and doneness are in Temperature; how each method uses the oven is in Cookies, muffins and biscuits and Cakes and frosting.